GPIO Out (QIO-GP8x8)

The GPIO Out component represents the GPIO OUTPUT connection pins on the rear of the QIO-GP8x8. Use one of the included 10-position Euro connectors.

+12V

12V DC, 0.1A output.

1-8

Eight outputs, user-configurable in the component Properties. Pins 1-8 are the equivalent of pins 1-8 in the Q-SYS Designer Software GPIO Out component.

Ground

Signal ground reference for GPIO output connections.

This component does not have standard input and output pins. See Control Pins.

QIO GPIO Out Properties

Name

The Name may contain ASCII letters 'a' through 'z' (case-insensitive), the digits '0' through '9', and the hyphen. Names cannot begin or end with a hyphen. No other symbols, punctuation characters, or blank spaces are permitted.

Note: This name must match the Hostname for the device as defined in Core Manager or Peripheral Manager.

Location

User-defined name that groups the component with other components in the same physical location – for example, "Rack 1" – or in the same organizational scheme.

Is Required

When enabled, and the device is not found on the network, the device is reported as 'Missing', which is an error condition. This is the default behavior. When disabled, and the device is not found on the network, the device is reported as 'Not Present', which is not an error condition.

Dynamically Paired

Indicates that this virtual component can be paired with the same type of hardware without changing the network ID of the hardware or the name of this component. Refer to the Q-SYS Core Manager Dynamic Pairing topic for more information. The default is 'No'.

GPIO-1 to 8

Type

Select the type of GPIO output:

• Digital Output (TTL 3.3V): 3.3VDC is supplied to the GPIO output pin when the Output control is enabled.
• Open Collector (200mA): 24V, 200mA max with pull-up to +3.3V.
• Raw: This mode is for advanced capabilities. If there is something you cannot do using the other choices, contact Q-SYS Support for assistance.

Graphic Properties

Label

Use the Label property to change the name of the component in the schematic. The Label property defaults to the component name. To learn more about renaming schematic elements, see Organizing Your Design.

Position

The coordinates reference a specific place in the schematic - for example,"100,100" (horizontal, vertical). 0,0 is the upper left corner of the schematic.

Fill

Sets the fill color of the component in the schematic.

Script Access Properties

Code Name

Displays the currently assign name for control access. You can use the auto-assigned name or customize it. Q-SYS will automatically check all Code Names in the design to ensure name is unique.

Script Access

Defines whether the component will be accessible by script and/or externally, or not at all. Choices include All, External, None (default), and Script.

Tip: Use Script Programmer Mode to quickly view the Script Access setting directly on the component in the design schematic without the need to disconnect from the Q-SYS Core processor.

Output

This button sends a 0 in the Off position and a 1 (3.3V TTL) in the On position.

Invert

This button is available when the Type is Raw.

Pin Name	Value	String	Position	Pins Available
Output (Digital Output, Open Collector, Raw)	0 1	false true	0 1	Input
Invert1	0 1	false true	0 1	Input / Output
1. Available in the Control Pins list when Type is set to Raw.

Q-SYS device GPIO output states are undefined during boot-up and design redeploy. In the following table, "While On" and "While Off" indicate the button setting as defined in the running design file. During a reboot or redeploy, the setting may toggle depending on the GPIO type before returning to the defined setting after the design starts running.

Bold text indicates a temporary GPIO setting during boot-up and redeploy.

QIO-GP8x8 GPIO

GPIO Type	While On	While Off
Digital Output	Stays On	Toggles to On
Open Collector	Toggles to Off	Stays Off
Raw	Stays On	Toggles to On