Responsalyzer

Input Pins

Measurement

Audio signal pins are represented by a () circle, and traditional wiring is represented by a thin black line. You can use Signal Names on audio signal pins.

By default, the Responsalyzer component only has two input pins available.

Output Pins

This component does not have any input pins available.

Responsalyzer Properties

RTA Bandwidth

Sets the bandwidth for the RTA measurements. The default is 1/12 Octave.

This sets the resolution logarithmically and should be adjusted along with the FFT size. You can choose from the following: 

• 1 Octave
• 1/3 Octave
• 1/6 Octave
• 1/12 Octave
• 1/24 Octave

FFT Size

Sets the resolution and response of the RTA measurements linearly.

The larger the FFT bin, the slower the response with greater resolution. A smaller FFT bin size gives faster response with less resolution. You can choose from the following: 

• 512
• 1024
• 2048
• 4096
• 8192
• 16384 (Default)
• 32768
• 65536

Time Constant Controls

Enable or disable the RTA Time Constant and Response Time Constant controls.

Graphic Properties

Label

Use the Label property to change the name of the component in the schematic. The Label property defaults to the component name. To learn more about renaming schematic elements, see Organizing Your Design.

Position

The coordinates reference a specific place in the schematic - for example,"100,100" (horizontal, vertical). 0,0 is the upper left corner of the schematic.

Fill

Sets the fill color of the component in the schematic.

Script Access Properties

Code Name

Displays the currently assign name for control access. You can use the auto-assigned name or customize it. Q-SYS will automatically check all Code Names in the design to ensure name is unique.

Script Access

Defines whether the component will be accessible by script and/or externally, or not at all. Choices include All, External, None (default), and Script.

Tip: Use Script Programmer Mode to quickly view the Script Access setting directly on the component in the design schematic without the need to disconnect from the Q-SYS Core processor.

There are two inputs to the Responsalyzer: Measurement, and Reference.

Measurement

Gain Bypass

Bypasses the Measurement Gain control when engaged.

Gain (dB)

Sets the Gain for the Measurement input signal.

Reference

Delay Bypass

Bypasses the Reference Delay when engaged.

Auto Set Delay

This trigger button sets the delay based on the conditions when the button was clicked

Delay (ms / seconds)

Manually sets the delay of the Reference signal.

Response

Response Graph

The scales for the Response Graph vary depending on the measurement method you select, see below.

When the X axis is frequency, the horizontal movement of the vertical crosshair cursor snaps to the bandwidth setting in the Responsalyzer Properties, 1 octave, 1/3 octave, and so on.

The vertical movement of the horizontal crosshair follows the magnitude or amplitude of the signal at the point of intersection with the vertical crosshair.

There are 10 octaves spanning the audio frequency range. The frequency is doubled (or halved) for each octave.

When Mag or Mag/Phase is selected, there is an orange line visible at the top of the graph. This line represents the Coherence of the Measurement signal compared to the Reference signal. The range is zero (at the bottom of the graph) to one at the top of the graph. Any coherence signal below 50% should be considered not usable.

Magnitude

Measures the magnitude of the Measurement input signal compared to the Reference Input signal over the audio frequency range. The green line is the Measurement Input signal.

Requires a Reference Input, typically the same source as the Measurement Input but prior to any EQ other DSP.

Magnitude / Phase

Same as the Magnitude selection but with the addition of a phase line (magenta) to compare the phase of the Measurement Input to the Reference Input. When both lines are the same across the frequency range, the phase is the same.

Requires a Reference Input, typically the same source as the Measurement Input but prior to any EQ other DSP.

Impulse

Measures the time difference of the energy pulse of the Measurement Input compared to the Reference Input. The Reference Input is at 0.0 on the X axis (not shown), and the Measurement Input pulse is displayed at the point on the X axis representing the time difference.

The Y axis displays the amplitude of the Measurement Input.

Requires a Reference Input, typically the same source as the Measurement Input but prior to any EQ other DSP.

Note: These two buttons display when Impulse is selected. Click the plus button to zoom in to display a range of 0 to 10.7 ms, and the – button to zoom out to display a range of 0.0 to 341.3 ms.

RTA

Measures the Measurement Input signal's magnitude over the audio frequency range. The RTA function does not use a Reference Signal.

Averaging

RTA Time Constant

Available only when Properties > Time Constant Controls is set to 'Yes'. Controls how quickly the RTA graph responds to changes in the signal.

Response Time Constant

Available only when Properties > Time Constant Controls is set to 'Yes'. Controls how quickly the Magnitude, Magnitude/Phase, and Impulse graphs respond to changes in the signal.

Pin Name	Value	String	Position	Pins Available
Auto Set Delay	Trigger			Input / Output
Clear 1	Trigger			Input / Output
Coherence	This control pin is a vector type output for use with a Control Script.			Output
Delay Bypass	0 1	no bypassed	0 1	Input / Output
Frequencies	This control pin is a vector type output for use with a Control Script.			Output
Gain Bypass	0 1	no bypassed	0 1	Input / Output
Impulse Response	This control pin is a vector type output for use with a Control Script.			Output
Impulse Response Length	This control pin is a vector type output for use with a Control Script.			Output
Magnitude Response	This control pin is a vector type output for use with a Control Script.			Output
Measurement Gain	-100 to 100	-100dB to 100dB	0 to 1.00	Input / Output
Phase Response	This control pin is a vector type output for use with a Control Script.			Output
Reference Delay	0 to 1.50	0ms to 1.5s	0 to 1.00	Input / Output
Response Averaging Time Constant	400 to 10	400ms to 10.0s	0 to 1.00	Input / Output
RTA	This control pin is a vector type output for use with a Control Script.			Output
RTA Averaging Time Constant	40.0 to 10	40.0ms to 10.0s	0 to 1.00	Input / Output
Short Impulse Response	This control pin is a vector type output for use with a Control Script.			Output
Update	This control pin is a vector type output for use with a Control Script.			Output
1. The Clear trigger is used to clear the graph when you change or mute the input.