Flex Out (Core 110f, 110c)

Inputs

Channels 1-8

By default, the Flex In component offers 8 Audio Inputs represented by a circle, and traditional wiring is represented by a thin black line.

Outputs

This component has no outputs available for this component.

Properties

There are no adjustable properties for the Flex Output component, other than Core Properties.

Core Properties

Name

The Name may contain ASCII letters 'a' through 'z' (case-insensitive), the digits '0' through '9', and the hyphen. Names cannot begin or end with a hyphen. No other symbols, punctuation characters, or blank spaces are permitted.

Note: This name must match the Hostname for the Core as defined in Core Manager. If you use Telnet or third-party external control, you must enter the Name exactly as it is entered here.

Location

User-defined name that groups the component with other components in the same physical location – for example, "Rack 1" – or in the same organizational scheme.

Model

Select your Q-SYS Core processor model. See Flex Out (Core 110f, 110c) for a list of selectable Core models.

External USB Audio

When enabled, you can connect an external audio device to the USB input and route audio to and from that device. See External USB Audio Device In and External USB Audio Device Out.

Network Receive Buffer

Adds extra buffer time to the default maximum of 1 ms.

Additional Network Receive Buffer time is useful in (rare) cases where the network latency through the network exceeds the default maximum. Additional network latency my be introduced by sub-optimal QoS functionality, some layer-3 routing implementations, long distances or large networks.

Because the specified additional latency is added both to transfers from IO Frames to the Core and from the Core to IO Frames, the additional system latency is twice the amount of additional receive buffer selected. Total system latency based on this setting is calculated and displayed immediately below the Network Receive Buffer property.

Clocking

Sample Rate

Selects the sample rate. Typically, 48kHz is used as the Sample Rate. In scenarios where Q-SYS is externally synchronized to a (video) house sync signal you would use 48kHz Pull Down as the Sample Rate.

Clock Source

The GPIO selection requires an external TTL level word clock or a GPS connection: pin 1 is signal, ground in is indicated by the ground symbol on either end of the connector. When you select GPIO In Pin 1 as the clock source, GPIO Pin 1 is no longer displayed. The clock source should be connected to pin 1 of the GPIO connector.

USB Bridging

These properties appear based on the USB bridging capabilities of the Q-SYS device. Refer to the USB Video Bridge and USB Audio Bridge topics to see what Q-SYS Core processors and peripherals support USB bridging.

USB Bridge Name

User-defined name given to the USB Bridge, from 1 to 24 characters. The Name may contain ASCII letters 'a' through 'z' (case-insensitive), the digits '0' through '9', and the hyphen. Names cannot begin or end with a hyphen. No other symbols, punctuation characters, or blank spaces are permitted.

Zoom Compatibility

If you are using the HID Conferencing component to control a remote computer running Zoom, set this property to 'Enabled.' Otherwise, when controlling another conferencing app such as Skype for Business, set to 'Disabled' (default). When this property is enabled, the USB Bridge Name property is disabled, and the USB Bridge automatically uses the name of the device for compatibility with Zoom's allowed device list – for example, "Q-SYS Core 110f" or "Q-SYS NV-32-H".

Tip: Enabling Zoom Compatibility may improve the user experience with macOS conferencing solutions.

USB Video Bridge

Enable the USB Video Bridge to bridge Q-SYS Mediacast streams to USB, enabling you to view Mediacast video on a connected computer. This exposes the USB Video Bridge component in the I/O-USB Bridge Inventory tree. To see what Properties are available when the USB Video Bridge is enabled, see USB Video Bridge.

UVC Camera Control

Only appears when USB Video Bridge is set to Enabled. When this is enabled (default), the camera can be controlled by far-end third party applications which support Relative Movement Commands. When disabled, the cameras cannot be controlled by the applications.

Video Formats

Only appears when USB Video Bridge is set to Enabled. See Video Formats for more information.

USB Audio Bridge

Provides the capability of passing audio via USB. When this is set to anything except 'Disabled', you can drag the Speakerphone and/or Sound Card components from the device's Inventory tree into your design. To see what Properties are available when the USB Audio Bridge is enabled, see USB Audio Bridge.

Disabled: (Default)
Speakerphone (1 x 1): Provides a speakerphone with an input and output component, each having 1 audio connection.
Sound Card (2 x 2): Provides a sound card with an input and output component, each having two (stereo) audio connections.
Speakerphone and Sound Card: Provides one speakerphone and one sound card with the same capabilities as described above.
Advanced – If supported, allows up to any combination of four speakerphone / sound cards.

Speakerphone Mode

This selection is available only when Speakerphone or Speakerphone and Sound Card is selected in the USB Audio Bridge property. Indicates if the Q-SYS design has Echo Canceling (EC) or Non-Echo Canceling (NEC). This information is provided to the PC or Mac operating system so it can determine whether or not to use its own echo canceling.

Graphic Properties

Label

Use the Label property to change the name of the component in the schematic. The Label property defaults to the component name. To learn more about renaming schematic elements, see Organizing Your Design.

Position

The coordinates reference a specific place in the schematic - for example,"100,100" (horizontal, vertical). 0,0 is the upper left corner of the schematic.

Fill

Sets the fill color of the component in the schematic.

Script Access Properties

Code Name

Displays the currently assign name for control access. You can use the auto-assigned name or customize it. Q-SYS will automatically check all Code Names in the design to ensure name is unique.

Script Access

Defines whether the component will be accessible by script and/or externally, or not at all. Choices include All, External, None (default), and Script.

Tip: Use Script Programmer Mode to quickly view the Script Access setting directly on the component in the design schematic without the need to disconnect from the Q-SYS Core processor.

Controls

Each control listed in the Analog and Digital sections, are one per channel.

Flex I/O

Output

Changes the associated channel to a Flex Output channel.

To switch back to a Flex Input channel, you must enable the channel in the Flex Input component.

Analog

Peak Input Level (dB)

Measures Peak Output level to the output device.

Output Mode

Mutes the output after the D-A converter and before the output.

Max RMS Output Level (dBu)

Controls the analog RMS output level after the D/A converter. This level is typically set slightly lower than the destination's sensitivity or maximum input level in order to avoid clipping the signal of a power amplifier. Varies in direct proportion with Output Gain.

Output Gain (dB)

The amount of gain applied to the outgoing analog signal. Varies in direct proportion with the Max RMS Output Level.

Digital

Peak Output Level (dBFS)

Measures the Digital Signal level prior to the D/A converter.

Clip

Red LED indicating if the signal is being clipped.

Clip Hold

Holds the clip indication until manually cleared.

Invert

Inverts the audio signal.

Mute

Mutes the digital audio signal.

Gain (dB)

Controls the gain of the digital audio signal prior to the D/A converter.

Status

Component status is conveyed with the Status LED and Status box, which uses both color and text to indicate the current condition:

OK: The device is functioning normally.
Initializing: The device is in the process of a firmware or configuration update, or the design is starting.
Compromised: The device is functioning, but a non-fatal problem exists. Refer to the Status box for details.
Missing: The device cannot be discovered.
Fault: The device is malfunctioning or is not properly configured. Refer to the Status box for details.
Unknown: This status appears during a Core reboot (for example, during a firmware update), or when a design is being uploaded to the Core and before it has started running.
Not Present: If applicable to the device, this status appears when the device is not connected to the network and its Is Required component property is set to 'No'. This status also appears if the device component's Dynamically Paired property is set to 'Yes', pairing has not been assigned in Core Manager, and the device component's Is Required property is set to 'Yes'. See Dynamic Pairing.

Control Pins

Pin Name	Value	String	Position	Pins Available
Analog Level (Peak Output Level (dBu)) meter	-120 to 20	-120 dB to 20 dB	0.000 to 1.00	Output
Clip	0 1	false true	0 1	Output
Clip Hold	0 1	false true	0 1	Input / Output
Digital Level (Peak Output Level (dBFS)) meter	-100 to 20	-100 dB to 20 dB	0.000 to 1.00	Output
Flex Output Enable	0 1	false true	0 1	Input / Output
Gain	-100 to 20	-100 dB to 20 dB	0.000 to 1.00	Input / Output
Invert	0 1	normal invert	0 1	Input / Output
Max Level (dBu)	-40 to 20	-40.0 to 20	0 to .988	Input / Output
Mute	0 1	unmute mute	0 1	Input / Output
Output Gain	-31 to 0	-31 dB to 0 dB	0.000 to 1.00	Input / Output
Output Mute	0 1	unmute mute	0 1	Input / Output
Status	0 1 2 3 4	OK (green) Compromised (orange) Fault (red) Unknown (red) Updating (blue)	0 0.250 0.500 0.750 1.00	Output