E-mailer

• You must be in the Run Mode to send email. If you enter any information in the Emulate mode, it remains in the E-mailer when you go to the Run mode. E-mailer supports only one outgoing e-mail at a time.
• Messages can be a maximum of 16 KB in size.

In this example, we are using a Status Combiner to verify the status of both our Amplifier and our Core. If the Status Combiner shows a fault in the status, a Momentary Button will trigger an outgoing E-mailer. However, first, it will go through a delay, long enough to capture the Last Entry of the Event Log, and then e-mail that information.

E-mailer Properties

This component has no configurable properties.

Graphic Properties

Label

Use the Label property to change the name of the component in the schematic. The Label property defaults to the component name. To learn more about renaming schematic elements, see Organizing Your Design.

Position

The coordinates reference a specific place in the schematic - for example,"100,100" (horizontal, vertical). 0,0 is the upper left corner of the schematic.

Fill

Sets the fill color of the component in the schematic.

Script Access Properties

Code Name

Displays the currently assign name for control access. You can use the auto-assigned name or customize it. Q-SYS will automatically check all Code Names in the design to ensure name is unique.

Script Access

Defines whether the component will be accessible by script and/or externally, or not at all. Choices include All, External, None (default), and Script.

Tip: Use Script Programmer Mode to quickly view the Script Access setting directly on the component in the design schematic without the need to disconnect from the Q-SYS Core processor.

The controls listed below are divided into sections to match the Control Panel sections.

E-mailer

Send

Momentary button to send the e-mail.

To

Must be a valid e-mail address. Multiple addresses can be entered, separated by a semicolon, comma, or space. Check with the carrier for the Mobile Phone to determine the format of the e-mail address you would use to send e-mail to the phone; each carrier is different.

Subject

Must contain some text.

Message

Must contain some text.

Status

Sending - Yellow

Send Succeed - Green

Error ¹ - Red

1. Errors can include: (parenthesis are explanations)

• 'To' field is empty (must contain valid e-mail address)
• 'To' field is malformed (must be valid e-mail address format)
• 'Subject' field is empty (must contain some text)
• 'Message' field is empty (must contain some text)
• 'From' field is empty (must contain some text)
• sendmail: MAIL FROM:< from address> failed (must be valid e-mail address format)
• Cannot send e-mail while emulating (must be in Run mode)
• sendmail: cannot connect to remote host ( IP address): No route to host (must be valid e-mail server IP address)

Configure

From

Must be a valid e-mail address.

If the e-mail was undeliverable, the failure return e-mail goes to this address, not the Core. If the person to whom the e-mail was sent replies to your email, the reply goes to this email address.

Password

If a password is required by the e-mail server, enter it in this field.

Server

IP address of the outgoing SMTP (Simple Mail Transfer Protocol) mail server from which the email will be sent. Do not use a server name unless the core is configured to use DHCP and the DHCP server provides a name server address, then the Sever field can contain the name of the outgoing SMTP mail server rather than the IP address. For more information, see Configuring SMTP Servers.

Tip: You can search the Internet for the server name, e.g. hotmail outgoing mail server, then in a command prompt window ping the server name to get the IP address.

Server Requires Secure Sockets Layer (SSL)

If you are using a mail service that requires SSL, click this button to enable SSL. If the mail server operates on a non-standard port (it might), you must append a colon followed by the port number to the IP address.

Some organizations with their own mail servers may not require SSL for access within the company. In this case, do not use the SSL option.

As email providers have increased security requirements for 3rd party clients, Q-SYS allows you to customize the port used for outgoing connections.

Note: Nearly all services and organizations require two-factor authentication. To take advantage of SMTP configuration in QSD, you must first have two-factor authentication enabled on your email account, otherwise you will receive an error that the email could not be sent.